Bringing Power Core analogue outputs into legacy processor chains

Power Core analogue outputs can feed an older transmitter processor without replacing it, but the junction needs deliberate electrical and operational design. The practical test is whether level, impedance, grounding and monitoring stay predictable when both systems are in service.

Many Australian stations still operate FM or AM chains while digital radio services expand. ACMA licence conditions and the Broadcasting Services Act 1992 continue to apply to analogue services, while regional coverage, emergency continuity and existing processor investment support a hybrid approach.

Map the signal path first

Begin with a signal-flow diagram that names every conversion point. A Ruby console, automation playout system or contribution feed may reach a Power Core audio node, an analogue output card and the transmitter processor. Label audio, clock, control and emergency routes separately so a routing mistake is not mistaken for a transmitter fault.

Inspect the processor’s manual and rear panel before adapting anything. Some units accept balanced professional line input; others offer unbalanced connections or a single mono input. Confirm whether inputs are bridging, terminated or intended for a particular source impedance. If the Power Core output can drive the load directly, preserve that arrangement.

An external network-to-analogue bridge becomes relevant only when the processor needs an electrical interface the node cannot supply. If one is needed, its formats, latency, channel mapping and galvanic behaviour should be checked against the interface requirements described by cxSilicon technology.

Protect the analogue connection

Treat the analogue connection as a signal path, not a bundle of loose audio wires. Use screened twisted-pair cable, secure connectors and a short run from node to processor. Keep it away from transmitter feed lines, mains switching equipment and high-current lighting loads. In Sydney and Melbourne, dense rooftop transmitters and shared inner-city buildings make isolation from RF and switching noise especially valuable.

Measure the node’s output with the processor disconnected, then connected. A balanced output can develop an earth loop if the systems carry different earth potentials, while an unbalanced input can expose noise that a balanced input would reject. A clean station earth and properly terminated shield reduce both risks; an audio analyser can reveal hum, RF pickup and intermittent opens.

Australian sites commonly use 230/240 V, 50 Hz mains, so transformer hum is a familiar clue. Check the rack supply and processor input stage rather than assuming every periodic waveform originates at the transmitter. Under the approved test procedure, isolate each source one at a time to separate local interference from a fault in the Power Core output card.

Match levels and processing

Set levels with a calibrated meter and repeatable programme source. Establish the Power Core output gain, confirm voltage at the processor input, and leave headroom for programme peaks and the processor’s limiting action. Feed the processor at its intended operating level, not at the maximum the hardware will accept.

Australian FM chains commonly use 50 microsecond pre-emphasis, so alignment must account for that curve. Measure the processor’s input before applying pre-emphasis, then verify final response with test tones swept across the audio band. Broadband source material, pink noise and an inter-station sweep can reveal errors that a single tone would miss.

Check channel identity and phase as well as level. A stereo route should preserve left and right, while a mono path may need an intentional sum with the correct phase relationship. Compare meter readings, switch between normal and bypass settings, and listen for overload, pumping or image shift. Record any limiter or gain-reduction indication.

Separate control from audio

Keep the new audio route separate from control and automation wherever possible. Power Core can supply the routed feed and independent metering, while the legacy processor retains its established functions. Lawo’s VisTool automation guidance explains how studio software can coexist with an existing radio automation system without conflating audio switching with playlist control.

That separation simplifies fault finding and protects a familiar on-air chain during a network problem. A documented fallback can use the previous source or a locally generated emergency bed, subject to the station’s approved procedure. Any route change should be observable at the processor, transmitter and monitoring system, with alarms sent to the duty operator.

Regional services outside Brisbane and Perth often run unattended overnight and depend on dependable analogue backup for large catchments. Automatic mute behaviour, loss-of-signal timers and alarm escalation deserve an end-to-end test. Agree a small set of readings—input level, channel presence and alarm state—for the station log, using the same vocabulary across different shifts.

Prepare a controlled handover

Bench-test before touching the transmitter. Sweep the complete chain, record output settings and processor trim positions, and repeat the reference measurement after any cable or load change. The comparison below gives the handover team a consistent place to record the values that matter.

Check Power Core analogue output Legacy processor input Recorded result
Electrical format Verify balanced or unbalanced connectors and termination Confirm the supported input type and sensitivity Cable, adaptor and operating level
Level Measure the configured output in dBu Measure at the input before processing Operating level and headroom
Channels Confirm mono, stereo or independent outputs Confirm the accepted layout and mono-sum behaviour Left, right and mono routing
Signal quality Check noise, hum, clipping and RF pickup Check limiting, gain reduction and mute indication Acceptable reference readings
Monitoring Use independent digital metering where available Record processor meters and fault indications Alarm and logging method
Changeover Test the configured bypass or fallback route Confirm mute, timer and fault response Approved rollback procedure

Build a make-ready sheet around those results, including the accepted operating window and rollback route. If the processor’s documentation or electrical details remain uncertain, confirm them with Lawo’s broadcast support team before changing a live input. Keep the labelled rollback procedure available until stability, off-air and failover checks pass.

The next concrete step is to book a supervised maintenance window for the first end-to-end measurement.

A wide modern broadcast studio with warm amber and charcoal tones, sleek audio mixing console glowing softly under dim lighting, calm and professional atmosphere